This includes some Windows XP features such as file system security, encrypting file system (EFS) settings, disk quotas, and Remote Storage. This occurs after your computer has restarted twice and after Setup has collected the necessary configuration information, but before Setup is complete. /debug[level]:[filename] Creates a debug log at the level specified, Local access available only through WindowsÂ 95 OSR2, WindowsÂ 98, and WindowsÂ 2000. Make sure the floppy has Format.com on it. http://wowtechminute.com/windows-98/how-to-install-windows-98-on-a-modern-computer.html
As the progress bar inches across the screen, your hardware is being detected, though there is no mention of this onscreen. There are four basic steps that should be followed before doing either an upgrade or a fresh installation: Check and make sure your computer can run Windows 2000. Obviously, this makes the maximum drive size for NTFS much greater than that for FAT, and as drive size increases, performance with NTFS doesn't degrade as it does with FAT. Doesn't W2k/XP setup need files from the subfolders in \i386? "copy *.*" does not take subdirs with it.
Then you would boot your laptop from a DOS floppy disk, reformat (fdisk) and repartition the hard drive to remove XP and its NTFS file system, then install Windows 98 from VGA or higher resolution monitor. Fdisk by default uses Disk 0 (or the primary master disk). The UDF overrides values in the answer file, and the identifier determines which values in the UDF are used.
If the existing partition is too small but you have adequate unpartitioned space, you can create a new WindowsÂ 2000 Professional partition in that space. If you want your programs to run on both operating systems on a dual-boot computer, you need to install them from within each operating system. You can find out the secret to adding and removing optional components after installation in my technology showcase, Removing Windows components after installation, however. What Is The Minimum Number Of Partitions That The Mbr Partitioning System Can Support Full text and property indexing Â— Allows fast searching and retrieval of files and documents.
In the next step, the curiously titled Personalize Your Software (Figure 22), you are asked to supply a name (required) and an organization (optional). Dual Boot Windows 98 And Xp The first place to start is with your motherboard and its Bios. Get A Personal Digital Certificate Get AOL Not To Block Your Mail Get Better Security Zone Control of My Computer Get Help From Volunteer Forums How to Fix a Broken Internet If you're upgrading a dual-boot computer, you will not be able to gain access to NTFS partitions from any operating system other than Windows NT 4.0 with SP4.
To create Setup startup disks Insert a blank, formatted disk into the floppy disk drive, and insert the Windows 2000 Professional CD into the CD-ROM drive. While Installing A New Operating System Or Booting Diagnostic Software The Typical Boot Sequence Is A fresh installation will prevent you from migrating any problems that may relate to the former operating system, such as incorrect drivers, settings and incompatible files to Windows 2000. Note: SETUP The Setup wizard will gather most of the information it needs, including regional settings (except for final locale settings), names, and passwords. The first choice is identical to the way Windows NT 4.0 works: The first time the system boots, you login as Administrator and, hopefully, create at least one other user account.
However, there are specific reasons that you might want to use another file system. https://www.microsoft.com/resources/documentation/windows/xp/all/proddocs/en-us/dual_booting.mspx Follow the prompts. How To Install Windows 98 Over Windows Xp Thanks for your help! Which File System Contains Support For Efs Your system must bet set to boot from the floppy drive.
The log levels are as follows: 0-severe errors, 1-errors, 2-warnings, 3-information, and 4-detailed information for debugging. weblink If you really want an earlier version of Windows, then Windows 2000 is as far back as you should consider going. Enter the command edit C:\config.sys Type the following: DEVICE=C:\OAKCDROM.SYS /D:MSCD001 Save and exit as you did before Remove your floppy disk, insert the Windows CD and restart the computer. If your computer is already connected to a network, you should obtain the following information before you begin Setup: Name of your computer Name of the workgroup or domain TCP/IP address Install Windows Xp From Dos Bootable Flash Drive
Microsoft has developed, and continues to update, a list of all Windows 2000 Professional certified programs. Leave the floppy disk in the drive, since there is now no operating system on the hard disk. Although WindowsÂ 2000 Professional requires a minimum of 650 megabytes (MB) of free disk space for installation, using a larger installation partition provides flexibility for adding future updates, operating system tools, and http://wowtechminute.com/windows-98/how-to-install-windows-98-from-cd-step-by-step.html Thanks in advance, sam Oct 21, 2005 #12 Tedster Techspot old timer.....
You have backed up your current data files, such as documents, email, pictures etcetera, so that you can recover them after the installation should it prove successful for you. Research How Your Smartphone Might Sync With Your Computer's Os When the command prompt comes up, use FDISK to create one or more partitions on the hard drive. Microsoft includes a sample answer file, Unattend.txt, in the I386 folder on the Windows 2000 Professional CD.
Your current operating system is Windows 3.X, which does not support an upgrade to Windows 2000. The syntax of the Winnt32 command is as follows: winnt32 [/s:sourcepath] [/tempdrive:drive_letter] [/unattend[num]:[answer_file]] [/copydir:folder_name] [/copysource:folder_name] [/cmd:command_line] [/debug[level]:[filename]] [/udf:id[,UDF_file]] [/syspart:drive_letter] [/checkupgradeonly] [/cmdcons] [/m:folder_name] [makelocalsource] [/noreboot] where: /s:sourcepath Specifies the source location of The drive will run for a moment and return. Technology Enables You To Carry A Powerful Navigational Aid In Websites When the files are copied, setup will automatically reboot your system (Figure 13).Windows 2000 setup, part three: GUI mode At this point, you've got a bare Windows 2000 system installed, one
but option k (oakcdrom.sys is not always on 98 bootdisk). Note: The setup startup disks contain different information than the Emergency Repair Disk, so be careful! A little text utility will come up (Figure 2) . http://wowtechminute.com/windows-98/windows-98-ethernet-drivers.html This technique uses two command line utilities, Fdisk and Format.
Just ignore it and continue setup anyway. FDISK will ask if you would like to make this partition active - YES!) Restart the computer with the floppy disk inserted. All of the information and drivers necessary to access to the network share that contains the Setup files. k - Enter the command copy A:\oakcdrom.sys C:Click to expand...
Check and make sure that both your hardware and software are compatible with Windows 2000. You mean unplug the removable floppy drive and replace it with a removable CD-ROM drive on a laptop? Windows 95 OSR2, Windows 98, Windows 2000, and Windows XP support FAT32 volumes.However, if you format a Windows NT 4.0, Windows 2000, or Windows XP volume with any file system other than NTFS, you will lose all NTFS-specific features.