Home > Power Supply > P2 Connector On Power Supply

P2 Connector On Power Supply

Contents

Power Protection Types--In this section you learn about devices that can protect your computer from over and under voltage issues. Mobos cost more and replacement is more involved so save that for last. * Note! Use the procedure outlined next to find the actual cause of a dead system. Page 1 of 15 Next > + Share This 🔖 Save To Your Account Related Resources Store Articles Blogs There are currently no related titles. http://wowtechminute.com/power-supply/best-power-supply-2016.html

On these boards, the manufacturer may instead number the last pin. These cables carry power and signals between various subsystems and components of the PC. I was also wondering about the fact that the card might still be half-powered when the rest of the computer is turned off. The power supply rating is found on the top or side of the power supply, along with safety rating information and amperage levels produced by the power supply's different DC outputs. http://www.informit.com/articles/article.aspx?p=31105&seqNum=4

P2 Connector On Power Supply

You may be able to use a needle to pry the block out far enough that you can extract it with your needlenose pliers. Use an isolation transformer if there is any chance of contacting line connected circuits. We also buy a disc wallet for each PC we buy or build. If these voltages are OK, Skip the following and go on to the next section.

An errant tab at best blocks the port, rendering it unusable, and at worst might short out the motherboard.After you position the motherboard and verify that the back-panel I/O connectors mate Unfortunately, a simple DVM won't show you whether there is AC ripple on the DC voltages, which can cause all sorts of problems if it's bad enough. The internal circuit should contain the LED's, a 15 ohm resistor to limit the maximum surge current when the PTC is cold and the special PTC film-thermistor. P5 Connector Power Supply Square Peg, Round Hole System designers attempt to avoid two potential dangers with regard to PC cables.

Page 1 of 2 Next > + Share This 🔖 Save To Your Account Related Resources Store Articles Blogs 31 Days Before Your CompTIA A+ Certification Exam (Digital Study Guide): A If it is still incorrect (logic level 1) you either chose the wrong type of power on circuit (Normally open or closed) or the motherboard is bad. If the motherboard has a similar connector, there's no problem, but sometimes that cable needs to connect to a motherboard connector with two adjacent pins. You may need to tilt the motherboard slightly down towards the I/O template to slip the back-panel connectors easily under their corresponding grounding tabs without damage.

Everything relies on power. Atx 20-pin Connector Make a single stripe across both cable connector and plug and you'll have a visual confirmation that they align correctly. Another alternative is to seek professional assistance. However, in older buildings, or during times of peak demand, power conditioning might still be necessary.

P4 Connector

up vote 1 down vote favorite One of my older computers has a 365-watt power supply that, for various reasons, cannot be replaced with a new power supply. http://electronics.stackexchange.com/questions/33190/how-can-i-power-my-6-pin-pci-express-card-without-using-an-atx-power-supply See the section: The series light bulb trick. P2 Connector On Power Supply For a card that's well and truly stuck, you may need a second pair of hands to apply downward pressure on the motherboard itself to prevent it from flexing too much Dell Atx Power Supply Pinout It might be a compromise, but I think I would regret investing hours/days of tinkering into this old computer. –Jourgen Jun 6 '12 at 17:34 add a comment| up vote 0

Both can damage or destroy equipment and can come through data lines (such as RJ-11 phone or RJ-45 network cables) as well as through power lines. have a peek at these guys All fans (except CPU and PSU), optical drives, floppy drives, USB devices are disconnected and all adapter cards including any graphics adapter are removed. This may not be as easy as it sounds. Thus, controlling the pulse width of the Q1 on-time determines the amount of power available from the output. Motherboard Power Switch Connector

Monitor while discharging and/or verify that there is no residual charge with a suitable voltmeter. After reading the responses here, I've decided to simply purchase a low-end graphics card that does not require additional power. –Jourgen Jun 6 '12 at 16:59 add a comment| up vote But we need your help. check over here If you're competent to work around live DC voltages in an open case, try to force the power supply on by shorting the green wire (pin 16, power_on) to any of

Oddball Cables Rather than using pins and holes, the connectors used on some cables for example, modular telephone cables and 10/100/1000BaseT Ethernet cables use other methods to establish the connection. A Connector On A Motherboard That Consists Of Pins That Stick Up From The Board Reconnect your meter leads to ground and 5v standby (Pin 9). Ribbon cables provide a way to organize the wires required to connect devices like drives and controllers, whose interfaces require many conductors.

Prowse Nov 24, 2009 📄 Contents ␡ Understanding and Testing Power Power Devices Power Supplies Additional Reading and Resources ⎙ Print + Share This Page 1 of 4 Next > This

Locating Pin 1 If you upgrade your system and it fails to boot or the new device doesn't work, chances are that you connected a ribbon cable backwards. For most of the tests you will be required to use a DMM or Digital Multi-Meter. High-performance PCI Express x16 video cards that require additional 12V power use a PCI Express six-pin or eight-pin power cable. P9 Connector Figure 4-17 illustrates the rear of a typical UPS unit.

Some combinations of adapter, case, and motherboard make it devilishly hard to install the adapter properly. It's not hard to find as it is the only one that has a purple wire going to it. If you must try this method, try connecting a known good fan to one of the aux power connectors and power up the PC just long enough to determine if you this content First, PATA allows two devices to be connected to each interface, one jumpered as master and the other as slave.

To remove an expansion card, proceed as follows: Remove the system cover and locate the expansion card to be removed. It is possible for both the PSU and Mobo to be bad! If the surge suppressor doesn't clamp fast enough, the surge can get through. The instantly downloadable book with 17 flowcharts and text is available for purchase here. ATX Power Supply Failure Diagnostics Note that these steps correspond with decision points on the flowchart